{
  "id": "bath-overflow-cover",
  "sku": "bath-overflow-cover",
  "title": "Bath Overflow Cover with 12 Suction Cups",
  "slug": "bath-overflow-cover",
  "price": 17.99,
  "currency": "EUR",
  "availability": "in_stock",
  "category": "sink-and-bath-plugs",
  "category_label": "Sink & Bath Plugs",
  "tags": [],
  "colors": [],
  "materials": [],
  "dimensions": null,
  "weight": null,
  "images": [
    "https://drains.eu.com/dropship-images/sink-and-bath-plugs/bath-overflow-cover/main-bath-overflow-cover.jpg",
    "https://drains.eu.com/dropship-images/sink-and-bath-plugs/bath-overflow-cover/bath-overflow-cover-4.jpg",
    "https://drains.eu.com/dropship-images/sink-and-bath-plugs/bath-overflow-cover/bath-overflow-cover-6.jpg",
    "https://drains.eu.com/dropship-images/sink-and-bath-plugs/bath-overflow-cover/bath-overflow-cover-7.jpg"
  ],
  "description_short": "A clear PVC disc with 12 strong suction cups grips any smooth tub surface, raising your usable water level by up to 9 cm without tools, glue or fittings.",
  "description": "The problem with a standard bath\n\nLie back in most bathtubs and something annoying happens. The water stops rising. You can keep the tap running for as long as you like and the level will not budge, because there is a small hole near the top of the tub quietly draining the extra away. That hole is the overflow, and it is the reason your knees, your chest or your shoulders keep ending up in the cold.\n\nThe overflow exists for a good reason. It stops a forgotten tap from flooding the bathroom floor and the ceiling below. But it was positioned by a plumber working to a standard, not by someone thinking about how deep you would like your bath to be. On many tubs it sits a full hand's width below the rim, which means a decent chunk of your bath is permanently unusable.\n\nA bath overflow cover is the cheap, obvious fix. It is a disc that seals the hole so water can carry on rising. Nothing gets drilled, nothing gets glued and no plumber is needed. When you are done, you peel it off and the bath goes back to normal.\n\nHow this one works\n\nThe cover here is a clear PVC disc, 14.8 x 14.8 x 5 cm, weighing about 90 g. On the back there are twelve suction cups. You wet the cups and the tub wall, press the disc over the overflow opening, and work your thumbs from the centre out to push the air from underneath. That is the whole installation.\n\nTwelve cups is more than many covers use, and the reason matters. Water pressing against the disc from the tub side is trying to push it off, so the holding force has to be spread around the edge. More cups means more contact area and a lower chance that one failing point unseats the whole thing.\n\nSarenius lists the gain at up to 9 cm of extra water level. Written down that sounds small. In the bath it really is not. Nine centimetres is roughly the difference between water lapping at your ribs and water sitting at your collarbone. It is also enough to cover your knees if you are tall and used to picking one body part at a time to keep warm.\n\nThere is a second benefit that people notice after a few uses. A deeper bath holds more water, and a bigger volume of water cools more slowly than a shallow one. You get longer before the bath goes lukewarm and before you reach for the hot tap again.\n\nWho it suits\n\nTall people are the obvious group. If you are over about 180 cm, most standard tubs were not built with you in mind, and an overflow sitting low on the wall makes that worse. The extra depth is the single cheapest improvement you can make to a bath you cannot replace.\n\nAnyone with a small or shallow tub benefits too. Compact bathrooms often get compact baths, and in those the overflow eats a bigger proportion of the usable depth. The same applies to shower baths, which are frequently shallower than a dedicated soaking tub.\n\nRenters are a natural fit. There is nothing permanent about a suction cover, so there is no modification to argue about at the end of a tenancy. You take it with you when you move. The same goes for holiday homes, caravans with a proper tub, and anywhere you do not own the plumbing.\n\nFinally, there are people using the bath for recovery rather than relaxation. Sore backs, stiff shoulders and tired legs all do better fully submerged in warm water. If half your back is in the air, you are only getting half the benefit.\n\nWhat to check before you order\n\nStart with the surface. Suction only works on a smooth, flat, non-porous area. Acrylic, enamel, pressed steel and fibreglass tubs are all good candidates. A tub wall with a textured anti-slip finish, visible pitting, limescale crust or old chips in that spot will not hold a seal reliably. Run your hand over the area around the overflow and see if it feels glassy or grainy.\n\nNext, measure. The disc is 14.8 cm square, so you need at least that much smooth, reasonably flat wall centred on the overflow opening. Gentle curves are usually fine because the cups have a little give. A sharp corner or a moulded ridge running through the contact area is a problem, because any cup that cannot sit flat is a cup that does nothing.\n\nThen check how your bath fills. This is the detail people miss. Some tubs have a combined overflow and inlet, where the water pours in through the same fitting rather than from a spout. On that design you cannot fit the cover first, because you would be blocking your own tap. You fill the bath, then fit the cover, and if you want to add more water you use a separate source such as a handheld shower head. On a conventional tub with a tap at the end, none of this applies and you can fit the cover before you start running the bath.\n\nFinally, think about safety. Blocking the overflow removes a backup. That is fine as long as you treat the bath the way you would treat a pan on the hob, by staying nearby and keeping an eye on it. Do not fit the cover, start the tap and go answer the door.\n\nGetting a good seal every time\n\nMost complaints about suction products come down to dirt rather than design. Soap scum, bath oil and body oils leave a slick film on tub walls, and that film is exactly what stops a cup from holding.\n\nThe habit worth building is simple. Before you fit the cover, wipe the contact area with a soapy cloth, rinse it, then wet both the tub and the cups with clean water. Press the disc on and push outwards from the middle. If a cup pops loose later, it is almost always because air got trapped under it during fitting.\n\nClean the cover itself the same way you clean the bath. Warm water, mild soap, a soft cloth. Skip the scouring pad and the bleach-heavy sprays, because abrasives scratch PVC and leave it cloudy, and strong solvents can make the cups go hard. Rinse, dry, store flat.\n\nStorage matters more than people expect. Suction cups that spend months squashed under something heavy lose their shape, and a cup that has lost its curve cannot create a vacuum. Hang the cover or lay it flat, somewhere dry and out of the sun.\n\nUsing it well\n\nA few small habits make the whole thing better. Fill the bath to just below the overflow with the cover off, then fit the cover and top up. That way the cups go on a tub wall that is still dry above the waterline, which is easier to seal.\n\nKeep an eye on the final level and stop the tap with a clear gap below the rim. You want depth, not a tide mark on the floor. Remember that when you get in, your body displaces water and the level rises, so leave room for yourself.\n\nWhen you are finished, pull the plug before you remove the cover. Taking the cover off while the bath is still full is awkward and does nothing useful.\n\nThe short version\n\nAn overflow hole decides how deep your bath can be, and it was positioned without asking you. This cover seals that hole with twelve suction cups and gives you up to 9 cm more water, which is the difference between a shallow dip and a bath you can actually sink into. It fits in seconds, comes off in seconds and leaves nothing behind.\n\nBefore you buy, check three things. That the wall around your overflow is smooth and flat for at least 15 cm. That your bath fills from a tap rather than through the overflow fitting. And that you are happy to stay in the room while the bath runs, because the safety backup is switched off while the cover is on.\n\nGet those right and it is one of those small purchases that quietly improves something you do every week.",
  "llm_summary": "The Sarenius bath overflow cover is a transparent PVC disc that seals a bathtub's overflow hole so the water level can rise higher than normal. It measures 14.8 x 14.8 x 5 cm, weighs about 90 g and is listed as 100% PVC. Twelve suction cups hold it to any smooth, clean tub surface, with no tools, adhesive or plumbing changes required, and it can be removed and reused. The manufacturer states the cover increases the usable water level by up to 9 cm, giving a deeper soak and better heat retention. Model number 1R-W81K-ABCV, supplied as one unit in one box. Colour is listed as transparent. Country of origin and warranty details are not specified by the maker.",
  "returnable": true,
  "return_policy": "14-day right of withdrawal from delivery under the Consumer Rights Directive 2011/83/EU, buyer pays the direct cost of return; two-year legal guarantee of conformity under Directive (EU) 2019/771 for faulty goods. Return postage on faulty goods is ours.",
  "shipping_profile": "standard",
  "warranty": null,
  "brand": "Drains Company",
  "gtin": null,
  "mpn": null,
  "condition": "new",
  "url": "https://drains.eu.com/bath-overflow-cover/",
  "canonical_url": "https://drains.eu.com/bath-overflow-cover/",
  "json_url": "https://drains.eu.com/api/products/bath-overflow-cover.json",
  "updated_at": "2026-10-12"
}