{
  "id": "galvanised-downpipe-leaf-guard-2-pack",
  "sku": "galvanised-downpipe-leaf-guard-2-pack",
  "title": "Galvanised Downpipe Leaf Guard, 2 Pack",
  "slug": "galvanised-downpipe-leaf-guard-2-pack",
  "price": 39.99,
  "currency": "EUR",
  "availability": "in_stock",
  "category": "gutter-and-downpipe-guards",
  "category_label": "Gutter & Downpipe Guards",
  "tags": [],
  "colors": [],
  "materials": [],
  "dimensions": null,
  "weight": "188 g",
  "images": [
    "https://drains.eu.com/dropship-images/gutter-and-downpipe-guards/galvanised-downpipe-leaf-guard-2-pack/main-galvanised-downpipe-leaf-guard-2-pack.jpg",
    "https://drains.eu.com/dropship-images/gutter-and-downpipe-guards/galvanised-downpipe-leaf-guard-2-pack/galvanised-downpipe-leaf-guard-2-pack-5.jpg",
    "https://drains.eu.com/dropship-images/gutter-and-downpipe-guards/galvanised-downpipe-leaf-guard-2-pack/galvanised-downpipe-leaf-guard-2-pack-6.jpg"
  ],
  "description_short": "A spring-shaped steel grid that compresses to fit downpipes from 87 to 100 mm, catching leaves, twigs and grit while rainwater drains straight through.",
  "description": "The one spot where gutters actually fail\n\nWalk around a house after heavy rain and you can usually spot the trouble in seconds. There will be a dark stripe down the render, a patch of moss on the brickwork, or a puddle that never quite dries out next to the wall. Nine times out of ten the cause is not the gutter itself. It is the outlet, the small round hole where the gutter empties into the downpipe.\n\nThat hole is the narrowest part of the whole system. A gutter channel is wide and forgiving, and leaves can sit in it for weeks without causing real harm. The outlet is different. It only takes a few sodden leaves, a bit of roof grit and a twig to form a mat across the opening. Once that mat forms, the gutter stops draining and starts behaving like a long, shallow trough. Water backs up, runs over the front lip, and lands exactly where you do not want it.\n\nA downpipe leaf guard is a small part that deals with a specific problem. It does not pretend to keep your gutters spotless. It keeps the outlet open.\n\nHow this guard works\n\nThe guard is a tapered cage of galvanised steel wire, roughly 12 cm tall. The lower end is narrower than the top, and the wire has enough spring in it to flex. You squeeze that narrow end between your fingers, lower it into the downpipe opening, and let go. The wire pushes outward against the inside of the pipe and holds the guard in place.\n\nThat flex is also what gives the guard its range. One size covers outlets from 87 mm up to 100 mm, which takes in the majority of standard round domestic downpipes. No screws, no sealant, no cutting. If you later need to take it out, you lift it.\n\nRainwater runs down the gutter, meets the cage, and passes straight through the open sides into the pipe. Leaves and larger debris cannot follow. They sit on and around the cage, usually in the gutter channel itself, where you can see them and reach them. Plenty of that material dries out on a sunny day and simply blows away.\n\nWhy galvanised steel matters here\n\nThere are three common materials for gutter guards, and they behave very differently over time.\n\nPlastic is cheap and light. It also goes brittle under years of direct sun, and brittle plastic in a gutter snaps when the first frost expands trapped water around it. Broken fragments then wash into the pipe, which is the exact problem you were trying to avoid.\n\nBare or mild steel holds its shape beautifully for a season, then rusts. A rusting guard stains the gutter, weakens, and eventually collapses into the outlet.\n\nGalvanised steel is steel with a zinc coating bonded to it. The zinc takes the weathering instead of the steel underneath. That is why it is the standard choice for outdoor metalwork that lives in water, from fence fittings to roof flashings. For a part that spends half the year damp, it is the sensible middle ground between the cheap option and the expensive one. This guard's silver finish is simply that zinc layer.\n\nOne practical note. Try not to scrape the coating badly during fitting, because scratches are where corrosion starts. Lower the guard in rather than hammering it down.\n\nWho gets the most out of one\n\nHouses near deciduous trees. Oak, sycamore, birch and lime all shed in volume over a few weeks in autumn. If your gutter blocks like clockwork every October, the outlet is almost certainly the choke point.\n\nGarages and outbuildings. These often sit at the back of a plot under overhanging branches, and nobody thinks to check them until water is running down the inside of the door. A garage gutter guard is a cheap fix for a building you rarely inspect.\n\nGreenhouses and lean-tos. Greenhouse gutters are shallow and narrow, so they clog fast. Keeping the outlet clear matters more here than on a deep house gutter.\n\nRain barrel setups. If you collect water, leaf mulch is your enemy. It slows the fill, clouds the water and makes it go sour in warm weather. A guard at the outlet keeps most of that material out of the barrel in the first place.\n\nFlat roofs. A blocked flat roof drain does not overflow somewhere harmless. It ponds, and ponded water sits on the membrane adding weight and finding weak seams. Keeping that outlet clear is worth doing properly.\n\nHow to choose and fit one\n\nStart with a measurement. Get the inside diameter of the downpipe opening, not the outside of the pipe, and not the gutter width. If that figure sits between 87 and 100 mm, this guard will fit. If it is smaller or much larger, or if the outlet is square, look for a different size.\n\nNext, think about where you will put the two guards in the pack. Most homes do not need every downpipe protected. Watch the roof during the next decent rain shower and see which corner overflows first. That is your priority. The second guard usually goes on whichever pipe sits closest to the nearest tree.\n\nFitting is straightforward. Clear the gutter channel around the outlet first, because dropping a guard into a bed of existing sludge just traps the sludge underneath. Compress the lower end of the cage, slide it down into the hole, and release. Give it a gentle tug upward to check it has gripped. It should resist without needing force.\n\nSafety is the part worth taking seriously. The guard itself is simple, but ladders are not. Set the ladder on firm, level ground at a sensible angle, have someone hold the base, and keep your hips between the rails rather than stretching sideways. If the gutter is above single-storey height or the ground is soft, this is a job worth handing to someone who does it for a living. Many gutter cleaning firms will fit guards while they are already up there.\n\nKeeping it working\n\nMaintenance is light but it is not zero. Twice a year is the rhythm most homes settle into, once after autumn leaf fall and once in spring when blossom, catkins and seed pods come down.\n\nPull the guard out, shake it off, and rinse it with a hose or under a tap. If grit has packed into the gaps between the wires, work it loose with a stiff brush rather than something metal that would scratch the coating. Let it dry, then drop it back in and check the grip is still firm.\n\nAvoid strong acidic cleaners. They attack zinc, which defeats the point of a galvanised part. Water, a brush and a bit of patience are all it needs.\n\nIf you live under pine, expect to do this more often. Needles are the one kind of debris that slips through almost every gutter outlet filter on the market, including this one. The guard will still catch the clumps and the cones, which is most of the volume, but it is not a complete answer to a pine tree.\n\nThe short version\n\nA downpipe leaf guard is a small, cheap part that solves one specific and very common problem. Gutters do not usually fail along their length. They fail at the outlet, where a handful of wet leaves can block the whole system and send water down the wall.\n\nThis one is a galvanised steel cage that squeezes into outlets between 87 and 100 mm, holds itself in place without tools, and lifts straight back out when you want to clean it. The zinc coating is there to handle years of sitting in rainwater. Two come in the pack, which covers the downpipes that matter on most properties.\n\nIt will not end gutter cleaning. It will move the work from somewhere you cannot reach to somewhere you can see, and that is usually the difference between a five-minute job and a call-out.",
  "llm_summary": "The Galvanised Downpipe Leaf Guard 2 Pack is a flexible steel grid that inserts into a gutter outlet to stop leaves, twigs and roof debris entering the downpipe while rainwater drains through. Each guard is made from galvanised steel in a silver finish and adjusts to fit downpipe openings from 87 to 100 mm by compressing the lower end during fitting. No tools, screws or sealant are needed. The manufacturer is listed as ABSINA, part number 101307-2, with product dimensions of 12 x 10 x 10 cm and a weight of 188 g. Two guards are included per pack. Country of origin is not specified by the maker, and no warranty term is stated.",
  "returnable": true,
  "return_policy": "14-day right of withdrawal from delivery under the Consumer Rights Directive 2011/83/EU, buyer pays the direct cost of return; two-year legal guarantee of conformity under Directive (EU) 2019/771 for faulty goods. Return postage on faulty goods is ours.",
  "shipping_profile": "standard",
  "warranty": null,
  "brand": "Drains Company",
  "gtin": null,
  "mpn": null,
  "condition": "new",
  "url": "https://drains.eu.com/galvanised-downpipe-leaf-guard-2-pack/",
  "canonical_url": "https://drains.eu.com/galvanised-downpipe-leaf-guard-2-pack/",
  "json_url": "https://drains.eu.com/api/products/galvanised-downpipe-leaf-guard-2-pack.json",
  "updated_at": "2026-10-12"
}